Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
364 results found
-
7 votes
-
Acoustical Calculations
Add acoustical calculations to the ductwork.
1 vote -
Swap & Copy Circuits
When copying circuits in the swap and copy dialog, multipole breakers do not copy to the new location as multipole breakers, they copy as single pole. It appears that you have to set the number of poles and their positions in the circuiting dialog before starting the copy/swap routine.
30 votes -
VAV Box Schedule
Create a schedule of VAV boxes, similar to the diffuser schedule.
38 votes -
Generic Schedule Creator
Have a way to create a generic schedule. The schedule will be informational purposes only, but it will be generated the same way as the other DM schedules so it will look the same.
29 votes -
Add multiple circuits to a single piece of equipment (ie. HVAC) one for each load.
Some HVAC and other pieces of equipment require multiple circuits for multiple loads inside each unit. Currently I have to create 2 pieces of equipment with the individual loads, overlay them, then circuit them.
29 votes -
Redundant Ground
Add "Redundant Ground" as an option for receptacles. Would add an additional ground wire to the tick marks and add an "RG" or similar label to the receptacle itself.
4 votes -
Device Customization blocks subfolders
Many of our projects require custom device blocks. We also have blocks for US standards, European standards, Middle Eastern standards, etc. The Customization folder is a mess. It would be nice if DM searched this selected folder and all of it's subfolders for it's blocks without having to add them each to AutoCAD's support paths.
2 votes -
Set Room Exhaust Rate
Specify the exhaust air requirements for rooms and use these numbers in the load calculations and duct design calculations.
27 votes -
Improve Indoor Lighting Level Report
Add "Allowed Watts / SF" as a field to rooms.
Add "Allowed Watts / SF" and "Total Allowed Watts" as columns to the indoor lighting schedule.
Add a "Totals" row at the bottom that totals the area, allowed watts, and computed watts.
3 votes -
Draw Circuit Loops Using Polylines instead of Arcs
When you loop from one device to another, be able to select that loop and break it in to two loops that can each individually be moved or broke. This way we can have "S" loops.
DM Note: When we implement this, it will probably be by allowing you to insert a loop using a pline. This will allow you to insert the loop however you want without any restrictions.
20 votes -
Make the note fields for panels and switchboard larger and editable
We need the note fields for Panels and Switchboards to be larger and editable like the Description, Model, and Note fields in the Light Fixture Project Schedule.
19 votes -
2 votes
-
Background Mask for Text
Have a mask on all the text inserted with Design Master that will hide anything on the drawing behind it to make it easier to read.
16 votes -
Create Separate One-Lines for Each LVD Group
I have Security, F/A, Lighting Control Panels, Audio, and Data groups and would like to be able to create separate low voltage one-line risers for them.
13 votes -
Keep Tick Marks on Broken Circuits
When a circuit is broken, keep tick marks inserted on one of the halves.
10 votes -
Photometric calculation schedule
I would like to suggest that the photometric calculation schedule be a combined schedule for all rooms instead of a dedicated schedule for each single room/space (or both options be available). We are typically asked to provide a single schedule that lists the room/space name in the first column and then the various footcandle columns.
2 votes -
A spreadsheet like table, simular to the fault calculations, that shows all the load calculation fields by panel, as they move to the final
A spreadsheet like table, similar to the fault calculations, that shows all the load calculation categories by panel, as they move to the final service calculation. We could then turn the load calculation footer off on the panel schedules and include this summary table in the drawings. It would also be great to figure out how the loads are adding up.
3 votes -
Metric
Support drawings with metric base units.
9 votes -
Allow diffuser tags to be moved and modified with standard AutoCAD editing commands.
It would be helpful to not have to use the "special" DM commands to manipulate the diffuser tags.
13 votes
- Don't see your idea?