Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
96 results found
-
Circuit Comments
Add comments to circuits in the Circuit Edit command. Transfer the comment value to the circuit and to the devices connected to the circuit.
This feature would allow additional information from a circuit to be scheduled on the devices. It would be similar to how DM currently pushes the breaker size to from the circuit to the device that can then be used in equipment schedules.
5 votes -
Save manual tick mark settings per user, not per project
Save the tick mark settings in the "Insert Tick Mark" command per user, not per project.
Currently the settings are saved per project. If multiple people are using the command in a project, their settings overwrite each other. If a single person goes to different projects, their settings are not remembered.
2 votes -
Add capability to adjust Target Conduit fill at Panel Level and in options + Warning when exceeded
Sometimes I prefer to over-size conduit for various reasons. However, if this is done manually at the panel level and then the feeder / ampacity changes, its very easy to have a feeder that exceeds 40% fill. Proving an option to adjust the maximum fill from 40% would allow the user to over-size conduits without manually selecting a size.
Also, adding an alert that warns you when a feeder exceeds 40% (Similar to the panel threshold warning) would be a great add.
1 vote -
Panel Edit - AIC Rating to include Size Automatically Option
It would be nice to have Electrical DM Panel Edit to have an option for Fault Current - AIC Rating to include "Size Automatically" option, on top of the standard AIC ratings DM provides in the drop down option.
2 votesThis request wouldn't be hard, but it is one we've specifically avoided to this point. Our thinking is that the AIC rating of a panel is an important enough setting that we want it reviewed and set intentionally by the engineer.
-
People in Room Setting
Add an option to input people in a room using "People / 1000 sf" as the unit. Currently you can input people using "SF / Person" which requires a conversion from the numbers provided by some codes.
1 vote -
Upsize wire based on circuit length
Upsize the wire based on voltage and length. Example is we often have a note to use #10's for 120V 20A circuit greater than 100ft in length and 277V 210A circuit greater than 150ft in length.
2 votes -
Grounding Electrode Conductor for Transformers
Size and label the grounding electrode conductor (GEC) for transformers based on NEC 250.66.
4 votes -
Option to not round GRD CFM
DM currently rounds CFM's of GRD's to nearest 5 CFM. I request an option to not have any rounding applied.
1 vote -
Match Runout size to GRD Neck Size Automatically (without running CALC)
Would you please consider an option to size the runout the same as the diffuser connection, without having to use the CALC function? That feature would be a big timesaver!
2 votes -
Change default circuit callout
Add an option for the default circuit callout inserted on the drawing when connecting a device to a panel. Currently it always lists the full circuit callout of panel name and circuit number (P-1).
1 voteThe solution in the current software is to circuit the device then use the “Modify Circuit Label” command to change the callout.
-
Customize Parallel Run Labeling
Add customization options for how multiple parallel runs are labeled for wires.
DM currently labels multiple sets with the number of sets in parenthesis before the full wire callout:
(3) 3-1/2"C, 4-600kcmil, 3/0G
If you are interested this feature, indicate in the comments how you would like the multiple runs labeled.
1 vote -
Adjust Transformer Taps
Be able to adjust transformer taps to take care of voltage drop.
1 vote -
Ability to add multiple set of conductor in a single conduit
Example:
For 400A feeder:
(2) 3"C, 3-250kcmil AL, 250kcmil AL N, #1 AL G
(1) 4"C, 6-400kcmil AL, 2-400kcmil AL N, #1 AL GInstead of each set take (1) conduit, would be good to get multiple set into a single conduit. This is mainly because installing (1) 4" conduit is cheaper than (2) 3" conduits.
1 vote -
Single Line-to-Ground Faults
Calculate single line-to-ground faults (NEC 230.95).
1 vote -
DC arc flash
Incorporate DC Arc Flash calculations. A lot of design work now has an element of renewable energy devices - solar, wind, etc. And many of those have battery 'peak shaving' capability. Being able to calculate both AC and DC arc flash given the electrical model will provide a one-stop-shop for arc flash. I would not rely so heavily on SKM. Thanks!
2 votes -
It will be good to add duct size(width&Height or diameter) in "Duct pressure drop report" of HVAC.
I've been using HVAC program to confirm weather other designers designed well or not, give an options to change his or her design and report these. So, it is essential to show which part's shall be changed in report. Fortunately, "duct length" can be included by checking option box.
1 vote -
I would like to be able to select a circuit number and highlight a device and draw a homerun, i.e. dedicated circuits, equipment, etc.
This would avoid the more cumbersome 2 step process
1. circuit device
2. draw homerunDepending on the job there are can be lots of dedicated circuits and/or pieces of equipment...
1 vote -
Customization of circuiting callouts
In circuiting callouts, allow the dash to be replaced by a custom string.
Example: Default circuiting callout is L1A-1,3,5. Allow us to make it say L1A: 1,3,5 or L1A CKT 1,3,5.
8 votes -
Room Names in Circuit Description
Provide an option for Room Names analogous to the "Conduit location" Option. Also consider other customization:
-Custom Room prefix - e.g. RM
-Option to include/exclude Name - e.g., RM 120
-Option to include/exclude Number - e.g., RM FIRE RISERRoom Names Location:
->Start of Circuit Description
->End of Circuit DescriptionCurrently the room names always go at the end, just like OOTB Revit. Having the option to put the room at the start would allow for better scheduling for when the intent is for circuits to be organized by room, like so:
https://i.postimg.cc/qMFD3DLx/2019-01-30-13-12-16-Window.png3 votes -
Spaces in Feeder Callouts
Be able to display feeder callouts with spaces after commas, instead of having all the wire sizes right next to each other.
Current Callout:
2''C,2#3/0,#3/0N,#6GDesired Callout:
2''C, 2#3/0, #3/0N, #6G2 votes
- Don't see your idea?