Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
365 results found
-
Equipment airflow available
Set the available CFM for a piece of equipment. If this value changes, update the airflow assigned in the downstream ducts.
1 vote -
Simpler way to Change fonts in all your panel/switch box schedules
Right now, one has to edit all the blocks of a panel schedule in order to simply change the font. There should be a way to set the preferred font for all these schedules. If there is a way, I don't know about it. When I first set up DM 10 years or so ago, I do not remember having to change every block, but it's been so long ago...
4 votes -
4 votes
-
Customizable tick marks
DesignMaster currently supports the following tick marks during an "Insert tick mark" operation:
- Hots
- Neutral
- Ground
- Iso ground
- Switch leg
- Traveller
- Space
We'd like the option to include customizable tick marks in addition to the ones already implemented above. For example, we include tick marks for low voltage cabling used to dim luminaries on our drawings.
I imagine the customization being performed through Design Master Electrical Options under the "Tick Mark Blocks" section. There'd be a "Customized tick mark 1 name" option and another option called "Customized tick mark 1 block". These customized tick marks would then show up in…
2 votes -
Add "Panel Neutral" in Revit MEP
Add "Panel Neutral" as a parameter to panels in Revit MEP.
Options for neutral would be:
50%
100%
133%
200%
NoneThis value would be a shared parameter for scheduling purposes. It would not be used in any calculations.
2 votes -
Default elevations for all electrical devices
You can specific a default elevation for light fixtures in the schedule. Expand this functionality to all types of electrical devices.
2 votes -
Do "Amps by Phase" using calculated loads on high-leg delta panels
High-leg delta panels are always unbalanced. The balanced 3-phase amps we display is not a good number to use when sizing these panels. The connected amps by phase does not account for largest motor loads or continuous loads.
Add the ability to determine the amps by phase using calculated loads. The largest motor, lighting, and continuous loads would all be calculated at 125%. All other loads would be calculated at 100%.
6 votes -
Tick marks for more than 1-pole, wire callouts for > #12
Add another option to "Homerun wire callouts and tick marks" labeled "Tick marks for more than 1-pole , wire callouts for > #12".
4 votes -
Color code room outlines by wall type.
So for example when modifying walls during a load calc. Exterior walls might be red, partitions blue, and interior walls (no heat transfer) green. This could even be expanded to visually shows with color walls that have windows or doors.
There have been many times when I've had to back check walls that were inadvertently called out as partitions instead of exterior. Color coding would give an instant visual clue where mistakes might have been made.
12 votes -
Right click when entering Duct Labels to Rotate Label
Similar to how you can right click to add leader lines when labeling diffusers, it would be helpful to be able to right click duct labels to rotate them instead of making this a two step process. Also, rotating it would remove the arrow that sometimes accompanies the duct label.
1 vote -
Compare Number of Balancing Dampers with Diffusers
A simple command that checks the number of volume dampers to the number of diffusers/grilles/registers in the database.
2 votes -
Change Voltage of Project
Be able to change voltage of a completed project for 208V to 240V and keep everything connected and circuited.
10 votes -
A spreadsheet like table, simular to the fault calculations, that shows all the load calculation fields by panel, as they move to the final
A spreadsheet like table, similar to the fault calculations, that shows all the load calculation categories by panel, as they move to the final service calculation. We could then turn the load calculation footer off on the panel schedules and include this summary table in the drawings. It would also be great to figure out how the loads are adding up.
4 votes -
Export schedules to excel
My estimators are always asking me if they can get my fixture or panel schedules in an excel format.
14 votes -
Actual Tonnage for HVAC Equipment
Add an option to specify the actual tonnage for HVAC equipment in the zone dialog. Use this value to display actual CFM / ton and other values.
3 votes -
Add "Clear Circuit" Button Back to "Circuiting" Dialog Box
Add the "Clear Circuit" command back to the "Circuiting" dialog box. This button will set all the breaker and branch circuit sizing options back to "Size Automatically", set all the fixed loads to "0", and set the circuit descriptions to be blank.
3 votes -
Duct Continuation
There may already be an option (please inform me as I am not aware) for a 'duct continuation symbol/fitting'. Currently I have to go back and Pline a goofy looking thing to indicate continuations in the ductwork. Any thoughts?
3 votes -
Manufacturer Name field included within Notes Settings of distribution equipment
It would be helpful when creating distribution equipment lists if there was an option for the manufacturer's name. Currently we have to use an unused Note key, rename the label for that key and then remember which Notes Setting corresponds to the list entry.
1 vote -
Add capability to have separate two line callouts for supply and return diffusers.
Add capability to have custom two line callouts for supply, return and exhaust diffusers as there is currently for one line callouts. Allow the second line to be blank for the return callout as there is often no need for cfm on the return callout. Same as a two line callout for supply diffusers and one line for return grilles.
2 votes -
Print Full Panel Schedules to 8.5x11 Sheets
Print full panel schedules, exactly as shown on the drawing, to a printer using 8.5x11 paper.
One specific use for these panel schedules would be to be submitted to Labor and Industries in Washington state for review.
3 votes
- Don't see your idea?