Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
198 results found
-
Add a hatch pattern to room definitions
When defining rooms, it is often difficult to determine which rooms have been defined and which have not, if an area gets surrounded. Adding a hatch pattern on its own layer would make it much easier to determine if you've included all room definition areas.
3 votes -
Subfeed breakers
Add specific support for subfeed breakers.
Be able to set the number of subfeed breakers on a panel (similar to how the number of poles is currently set on a panel).
Have the panel schedule update to document which breakers are subfeed. We likely would add a separator block between the branch circuit and subfeed breakers that you could customize. The default block would have a line across the schedule plus some text indicating branch circuit breakers above and subfeed below. You could then modify that as desired for your documentation purposes.
56 votes -
Improve combined homeruns
Be able to combine homeruns with different wire sizes.
Be able to combine homeruns from separate panels.
Be able to display a full wire callout for combined circuit homeruns, including calculating the conduit size required for all the wires.
14 votes -
Voltage Drop Based upon Connected or Other Load
Be able to specify that the voltage drop on a feeder should be based upon the connected or other load, rather than the calculated load.
One example of a use for this feature is a piece of equipment that serves a single motor. You want the voltage drop for the connected load of the motor, rather than the calculate load, which will be 125% of the motor load.
6 votes -
Label homeruns with feeder IDs
Label homeruns using feeder IDs like those used in the one-line diagram instead of full text wire callouts.
3 votes -
Copy panel and loads to new project
Be able to copy panels and other distribution from one project to another. The loads on the panel will be created as fixed loads in the new project.
3 votes -
Reset panel "Fixed Loads".
Often, I need to "start over" on a panel that I've assigned fixed loads. It would be handy to have a button that would clear every fixed load on the panel. Or even be able to select several circuits and clear those circuit's fixed loads.
5 votes -
On a one-line diagram, a vertical bus panel should have horizontal branch breakers--NOT vertical!
When you generate a one-line diagram, if you have panels that have a vertical bus, their branch breakers end up at the bottom of the bus and are vertical. The look like main breakers--not branch breakers. A work around for this is for every vertical bus panel, generate a riser diagram starting with that panel. Even this work around is not perfect, as you have to resize the vertical bus and fiddle with the branch breaker.
4 votes -
Show schedule notes on last column when schedule is split
Currently if a schedule has a "Maximum Schedule Height" set the schedule notes are placed at the bottom of the first column. It would be better to place them at the bottom of the last column (or at least have an option to place them there) since the last column is often shorter than the others.
2 votes -
Low-voltage looping
Be able to draw loops between devices for low-voltage lines, for connecting items like sensors and power packs.
6 votes -
Default label locations in blocks
Be able to specify locations for labels in blocks. When the labels are added to the block, they will be placed in the desired locations, rather than in the somewhat random default location they are currently placed in.
4 votes -
Homerun Note
Be able to add a note to a homerun callout.
5 votes -
Export Light Fixture Watts to Excel
Export the Energy Code Settings->Watts field from the light fixture schedule to Excel using the DM Electrical Excel Add-in.
4 votes -
Connect loops to fixtures on same switch first
When inserting automatic loops, connect devices on a switch together first rather than mixing up the loops when multiple switches are on a circuit.
3 votes -
Define fixed load by phase
When defining fixed load on a panel schedule allow entry of per phase loads on two and three phase circuits in stead of lumped loads, i.e., on 2-pole circuit be able specify a load for phase A and B on any of the demand categories.
2 votes -
Support Paralleled Generators Connected to Switchboard
DM does not currently support more than one source on the Normal side of an ATS or the EM side of ATS, however larger I-2, I-3 occupancies generally have paralleled generators connected to a switchboard. This feature would avoid cumbersome work arounds.
9 votes -
Electrical Symbol Legend
Add a Schedule of all blocks used in the project. This could be used a Symbol Legend for the Project.
46 votes -
please add a new column to the lighting fixture schedule for "KELVIN"
ADD NEW COLUMN IN LIGHT FIXTURE SCHEDULE FOR "KELVIN"
2 votes -
Light Fixture Settings - Different Blocks
The ability to define an egress fixture as the same fixture/block as the normal fixtures, with an option to turn a hatch on/off to differentiate. Similar to in Revit, where you can set an instance parameter and check it to turn fixtures into the egress blocks. The fixture type stays the same, only the visible block changes.
16 votes -
Voltage Drop in Equipment Schedule
Add "Voltage Drop" as a column to the equipment schedule. Would list the branch circuit voltage drop to a each piece of equipment in the schedule.
4 votes
- Don't see your idea?