Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
191 results found
-
A spreadsheet like table, simular to the fault calculations, that shows all the load calculation fields by panel, as they move to the final
A spreadsheet like table, similar to the fault calculations, that shows all the load calculation categories by panel, as they move to the final service calculation. We could then turn the load calculation footer off on the panel schedules and include this summary table in the drawings. It would also be great to figure out how the loads are adding up.
3 votes -
Insert Devices via command line
Be able to insert a receptacle/device without picking it from the 'Insert Receptacle' form. A command followed by the device name would prompt the user to place the receptacle like they just clicked "OK" after selecting a device.
2 votes -
Multi text search
implement Multi-Text search through out the menus.
So for example when searching through the Insert Receptacle menu and in my case we have several thousand pieces of equipment. if the equipment is called 'RX99S' instead of just allowing us to hit 'R' and starting us off at the beginning of the list of 'R' equipment allow us to type out 'RX99S' and design master go straight to the piece of equipment. this is a very simple change to the code in design master and would save tons of time on projects.
7 votes -
Select automatic conduit based on Type
When selecting conduit I want to be able to select the feeder as schedule 80 so that the only size option would be based on schedule 80. Then on another feeder I could select EMT for my circuits and the only option for auto sizing would be based on EMT. Finally, I would then have the option of adding the type to my one-lines and a conduit schedule.
11 votes -
Lighting loads - additional options
I like the recent addition of the general lighting loads, but there are a couple of additional things that I would like to see related to that.
- I think that the calculated load should include the greater of the general lighting load or the connected lighting load. The NEC states that the values for the general lighting loads are minimum values and that they may not be adequate.
Ok, so this is probably a low priority because the NEC values are pretty conservative. With the increased adoption of energy conservation codes it becomes less likely that the connected lighting load…
2 votes -
Export schedules to excel
My estimators are always asking me if they can get my fixture or panel schedules in an excel format.
13 votes -
Generator Load Calculations
Calculate generator loads correctly, mostly by being able to specify that certain loads should not be included in the generator load.
1 vote -
ADD SECURITY SYMBOLS TO LV OPTIONS
DOOR STRIKE/DOOR CONTACT
CAMERA
MOTION SENSOR
CARD READER
KEYPADJUST A FEW EXAMPLES...
2 votes -
Existing Loads & Metered Demand
Include, in options, the ability to not include existing (layered) items in panel, feeder, and service calculations. I'd like to enter the load to keep track of it, but have the ability to exclude it from the load calculations since "existing" would be included in the metered demand load.
1 vote -
Luminaire energy code settings should default to "input VA" for Watts & "schedule descrip." for description
This would save two extra input steps in most cases. You could still click into the box to edit the Watts and Description.
2 votes -
Add a select similar command for devices similar to AutoCAD and AutoCAD MEPs select similar command
I would like to right click on a device already on the plan, and hit select similar rather than having to open up a separate dialogue to pick a device/LVD/Light Fixture device, and then place it. In other words, I'd like to bypass the select device dialogue altogether whenever possible.
4 votes -
Print Full Panel Schedules to 8.5x11 Sheets
Print full panel schedules, exactly as shown on the drawing, to a printer using 8.5x11 paper.
One specific use for these panel schedules would be to be submitted to Labor and Industries in Washington state for review.
2 votes -
Convert panel schedules to tables
Convert panel schedules to use the AutoCAD table feature so they are more customizable.
2 votes -
Provide a button (or perhaps under the Cir Opts button) for quicker selection of "Display tick marks on loops"
I've given up on loop tickmarks for lighting loops (because of all the energy code relay and occupancy sensor requirements); but I still do tickmarks on power loops. It would be great to be able to more quickly toggle between displaying tickmarks on loops.
2 votes -
Equipment circuit label should be near the equipment symbol--not the equipment label.
We often turn off printing of equipment label/leader, and use a keynote number with arrow instead. But we have to move the circuit to the equipment symbol, because it ends up under the equipment label (which we are not printing).
2 votes -
Query Low Voltage Device
Query command does not show circuit connection for low voltage devices. We typically have low voltage devices connected to different panels, and querying the device to determine the panel to which it is circuited would be nice.
1 vote -
Automatically Add "ON" prefix to homerun labels for which a homerun already exists.
It is customary for circuits that are shared on opposite ends of a building or from one floor to the next to be identifed with multiple homerun symbols, with all but one of those homeruns labeled with "ON <Panel-Ckt>" rather than connecting with a loop. Currently, to do this, the homerun text itself must be modified, and this rarely works well because that text reverts back to the default <Panel-Ckt> text each time the circuits are updated.
1 vote -
Low-Voltage lighting systems - Transformers and light fixtures for 12 Volt and 24 Volt systems.
Make possible not only the easy DM insertion of these devices onto the lighting plan but also the ability to account for these in the panel schedule and load calculations.
2 votes -
Add horsepower of individual loads on mcc schedules
The MCC schedule doesn't have the ability to show horsepower values for the individual loads. This is important information for the MCC vendor for breaker and overload sizing.
7 votes -
Make circuit dialog box non-modal
Allow users to leave circuit dialog box up on screen while still manipulating floor plans.
3 votes
- Don't see your idea?