Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
379 results found
-
'Capped Ductwork for Future Use' command
This is similar to the 'end cap' command, but would draw a 'capped for future use' symbol on the end of a duct branch.
1 vote -
Paralleling Switchgear Support
Would be very helpful to be able to be able to have multiple sources connect to the same bus. We have had numerous situations where we have had Geneva type switches, multiple kirk-key input as well as paralleling switchgear situations where we were unable to find a "work-around" using this software. This is becoming especially common with ConEdison now permitting the paralleling of electrical sources.
1 vote -
Schedules
Having the ability to adjust the width of a schedule in the drawing model, instead of the schedule toolbox.
1 vote -
Better default panel clearances
Have better default values for panel clearances, including options to have it vary upon the panel defition.
1 vote -
Populate MCC Information Based upon Equipment
The motor control center schedule includes several fields that could be populated from the information entered into the equipment connection devices. These include:
Disconnect fuse size
Starter NEMA size
Starter type (ie, starter description)However, these fields do not populate automatically when the equipment connection devices are circuited to the motor control center. Is there a way to make the motor control center fields automatically pick this information from the equipment connection devices when they are circuited to a motor control center? Is there a way to override automatically populating the starter information into the motor control center when the…
7 votes -
New and Existing Circuits / Breakers in Panel Schedule
Be able to show new and existing circuits on different layers in a panel schedule. The existing circuits would be on a lighter layer and the new circuits would be on a darker layer. The rest of the schedule could be on either the new or existing layer.
12 votes -
Demolition Layer Devices
I do not feel that the schedules should show counts for devices like receptacles and computer outlets that are on a demolition layer.
8 votes -
Equipment Database
Allow us to create an Equipment Database similar to the diffuser database which would include dimensions, and notes such as: electrical requirements, efficiency, performance data at design conditions, etc. The equipment should also be included in the takeoff report.
1 vote -
Insert Load Calculation Output on Drawing
Insert the load calculation schedules on the drawing.
21 votes -
HVAC - Allow for the input of design Notes
In the "Room Project Schedule" add a box which would allow for the addition of design notes. This would allow for the designer to document why certain values where chosen. When the loads are printed the notes would also be displayed for reference.
3 votes -
Highlight Footcandle Levels Below a Certain Level
It would also be nice if foot candle levels less than a certain value could be a different color. This would make it easier to spot levels below a certain threshold, like fc levels for emergency egress lower limits.
4 votes -
Redefine Panel Schedule Blocks
Add a command to automatically erase and reinsert panel schedules so that attribute locations are updated correctly.
Currently, you have to manually erase the schedule, redefine the block, and reinsert the schedule.
1 vote -
Adding Further Pipe Symbols
All of these symbols came up on one particular project, please leave comments on common plumbing symbols that I may have missed. Adding in these symbols and the corresponding isometric representations would greatly reduce the amount of time required to create each one of them by hand on both models. The following are the symbols that I found would be useful additions:
- Mixing valves
- Water heaters
- Grease interceptor
- Sample wells for grease interceptors
- Cleanout
- Cleanout to grade
- Two-way cleanout
- Backflow preventer
- Water filter
9 votes -
Size Transformer Feeders Differently than Other Feeders
Allow transformer feeders to be sized using different size wires than other feeders. In particular, this would be for sizing 800A feeders. Normal panels can use 500kcmil wires, but transformers require 600kcmil.
(The workaround for the moment is to use 500kcmil for your 800A automatic sizing and to manually size the transformers to 600kcmil.)
2 votes -
Set number of spare breakers
Add an option to require a set number of spare breakers on every panel. The other breakers in the panel would be listed as spaces.
12 votes -
Export Equipment List to Excel
Export a list of equipment connections and information to a file that can be opened and viewed in Excel. The file would be for post-processing only. Any changes to the equipment would still be made using the other DM commands.
28 votes -
Edit multiple rooms
Add a command to allow you to edit the settings on multiple rooms at a time.
10 votes -
Create Room Outlines Automatically
Detect room boundaries from the architect's XREF automatically and create rooms based upon it.
5 votes -
Command to Automatically Turn Photometric Layers On and Off
It would be nice to have ribbon menu icon commands to turn the photometric layers on and off as well as automatically turn the respective layer back on after doing a recalc of either general or egress lighting.
2 votes -
Custom circuit description for spaces with no breakers
Have a custom circuit description that is automatically used when the breaker size is set to "None" for a circuit.
1 vote
- Don't see your idea?