Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
367 results found
-
Different layer systems for different loops and tick marks on a circuit
We can assign layers based on one-line (panel) or circuit or devices however not all parts of circuit are on the same layer. I may run some in the slab and some in the walls. Having the ability toi use the manual loop tool to change the layer system would be helpful. Also having the ability to assign a device to multiple layers would be helpful as well.
Or have some of the loops new and some existing.
5 votes -
Different Layers for New and Existing Items in Schedules
Use different layers for new and existing circuits in panel schedules or new and existing equipment in equipment schedules.
1 vote -
Importing Revit Model Information
It would be a great tool if we can have the ability to import model information from Revit drawings which are done by architects. A simple feature would be importing the rooms. This would speed up the process and make designs happen faster.
2 votes -
Low Voltage Homerun With Keynote
On low voltage systems drawings (Fire Alarm, Security, CCTV) we treat homeruns differently than power and lighting homeruns. We do not use the circuit label, wire callout, or tick marks, but rather we use a keynote. If there was a “keynote homerun”, it would save us the time spent removing the wire call-out every time we create low voltage homerun.
6 votes -
Vertical Alignment of Schedules
Add an option to control the vertical alignment of text in schedule cells.
Currently everything is justified to the top of the cell. Make it so that text can be centered or at the bottom instead.
1 vote -
Modify design load calculations and output to accommodate VAV system selection
Modify design load calculations to more accurately size/select VAV boxes. The revised calculations would take into account the heat required to overcome the additional air supplied to the VAV box that is over and above the minimum required in the heating calculations. This will help since the additional air is typically at 55 degrees and will actually add heat load to the space in addition to that required by the envelope and minimum supply air. In some cases this can be a significant load.
2 votes -
For Energy Code compliance, the light Fixture Schedule should include a subtotal of watts for each fixture type, and a total of watts for al
For Energy Code compliance, the light Fixture Schedule should include a subtotal of watts for each fixture type, and a total of watts for all the fixtures on the posted schedule. That will help expedite the Lighting Power Density calculations required for Energy Code Compliance.
2 votes -
1 vote
-
MULTIPLE ARROWS
It would be nice to be able to have multiple arrows for 1 piece of text pointing to different devices
2 votes -
Create training material for the HVAC section.
The tutorial doesn't get into enough depth or cover everything, specifically the master schedule and project schedules and how they affect the project.
2 votes -
Selected device type to find that are uncircuited
Often I circuit items by device type, such as equipment first, then general receptacles, and finally lighting. Sometimes I only show the light fixtures or site lighting but don't ever circuit them as a lighting designer is taking that part of the contract. So under either situation if the symbols have already been placed and I do the “Highlight Uncircuited Devices” command, I get so many lines going all over the place that I can't find out which receptacles I haven't circuited. It would be nice under the Highlight Uncircuited Devices label you have a sub-selection of: Receptacle, Lights, Equipment,…
1 vote -
Manufactured Wiring (Modular wiring) NEC 604
Add wiring and symbols for manufactured wiring systems (NEC 604), MWS, Reloc etc
1 vote -
add sub-script option for junction boxes
Add subscript for junctions boxes like you did for low voltage devices.
1 vote -
Choose Fittings Used In Pressure Drop Calculations
Add the ability to choose the specific fitting type used when calculating pressure drop in duct systems. Currently, the fitting type is fixed.
1 vote -
Device information on hover
When you hover (or float) your mouse over a DM device, display information about that device in a tooltip.
For DM Electrical, possible information would include callout and circuit number
1 vote -
When a panel is designated as existing, the circuit descriptions (editable part in the circuiting form) start off with "EX"
When a panel is designated as existing, the circuit descriptions (editable part in the circuiting form) start off with "EX"
1 vote -
Selective Coordination
Comply with NEC Article 700 requirements for selective coordination of overcurrent protective devices in the supply side of emergency system.
5 votes -
Add Static Regain that balances duct system correctly
Current Static Regain calculation does not seem to calc and size ducts to balance system. The static regain should balance the system where the ducts split.
2 votes -
put alternating shading on successive rows in outputted html tables/reports
For example, when I print an HVAC load calculation report, the many row entries can be difficult to follow visually across the screen. This obviously won't be useful in absolutely every case, but an option to have a little bgcolor="#EEEEEE" every other line would be awesome.
1 vote -
Handle LED Lighting Better
Calculate the load based upon the length and the remote transformers.
6 votes
- Don't see your idea?