Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
358 results found
-
More MCC Stater Sizes
Is it possible to modify the list of standard starter sizes to include VFD, Soft Switch, etc? Or even to choose 'None' and just type it in the Description field?
I've used the ddedit command on the MCC schedule inserted into the drawing to manually modify it, but if anybody does a coordination this will be lost.
1 vote -
3 votes
-
Handle LED Lighting Better
Calculate the load based upon the length and the remote transformers.
6 votes -
8 votes
-
Minimum panel clearance width
For panels smaller than 30" width, increase the panel clearance width to 30" automatically.
3 votes -
Support feeder calcs for track lighting
See NEC 220.43(B). The connected load for the branch circuit is the sum of the wattage of the connected light fixtures. The demand load is an additional 150VA per foot. I would like a place to enter the number of feet of track on a branch circuit so the demand load is calculated correctly in the load summary. We currently accomplish this through a 'Variable Caclulated Load', but it might be more intuitive if there is a 'Length Variable Demand' option. Thank you.
2 votes -
Variable Pressure Drop for Diffusers
Using the maximum scheduled pressure drop for every scenario over inflates the pressure calcs. This is very important for low-pressure systems with low static terminal units such as ducted VRF and Fan Coil Units that max out at .25". Using the maximum scheduled pressure drop of say, .1" for air devices make it difficult to design low static systems accurately.
1 vote -
Multiple Switch Legs on a Single Switch
Allow a single switch to have multiple switch legs associated with it. Currently we require a separate switch for each switch leg.
13 votes -
The ability to easily copy all pipes including risers to other drawings.
Would be great to be able to copy all piping, including risers to other drawings. Even if you had the option to change risers to pipe I think it would be helpful and save time from having to chase down and draw all the risers a second time.
2 votes -
lighting report
Provide a check box in the Building Room dialog box to NOT include the room in the lighting report.
I have a job where I need room names to generate the names for the receptacle circuits in the panel schedule, but don't want the rooms to show up in the Indoor Lighting Levels report.
1 vote -
Equipment and Receptacle Short Circuit Calculations
Add the ability to select a checkbox for receptacles and equipment so that short circuit calculations are included for that device.
2 votes -
Premade fixture blocks
Premade blocks similar to what is used in both HVAC and Electrical could be inserted into the drawing with predefined fixture units. The fixture units would be stored into multiple headings with IPC and UPC fixture units. The connections would be there with predetermined heights as well.
12 votes -
Provide Minumum air flow calculations
If the minimum air flow is set in the calculation bases on a parameter such as air change rate, cfm/sq ft or a set cfm it would be nice to have that as a column in the calculation output.
2 votes -
Add an option to the "Duct: Edit Multiple" dialog that allows users to choose whether to preserve duct endpoint connections or not.
So if I query and individual duct section and change the elevation of either end, the ducts the ends are connected to also change elevation to preserve the connection between the endpoints. If I "edit multiple" on several duct sections and change the endpoint elevations, the other duct sections connected at those points do not change elevation to preserve the connection. Sometimes, changing the elevation of one endpoint without keeping any other endpoints attached is what I want, and sometimes I wish the connections were all preserved. I think there should be a drop-down, a radio button, or something on…
2 votes -
13 votes
-
Add Sections to Panels
Define how many breakers are in each section of panel. This would be used when creating a 84 circuit panel that is made up of 2 sections, each with 42 circuits.
For the panel schedule, include a separator between the sections.
When circuiting, do not allow 2 or 3 pole circuits to span the two sections.
12 votes -
Remember Location of Dialog Boxes
When a dialog box is moved, remember the location so that the next time it is opened, it is displayed in the same location.
2 votes -
5 votes
-
Number Circuits Sequentially in Panels
Allow panels to have the circuits in them numbered sequentially, rather than split odd and even.
1 vote -
Pipe breaks caused by only one set of pipes
Our plumbing drawings will typically be drawn with supply and drainage on the same drawing. It would be helpful if only the drainage piping caused breaks with drainage piping and the supply piping with only the supply piping. Additionally we place venting on a separate layer. I am thinking that you could place different pipe types into different categories and they would only affect pipe breaks on pipes in their category.
1 vote
- Don't see your idea?