Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
358 results found
-
Command to Automatically Turn Photometric Layers On and Off
It would be nice to have ribbon menu icon commands to turn the photometric layers on and off as well as automatically turn the respective layer back on after doing a recalc of either general or egress lighting.
1 vote -
Calculate General and Egress Photometrics in Same Boundary
It would be nice if we didn't need to create two photometric calculation areas. It would be great if one calc area could work for both general and egress calcs.
1 vote -
Add Standard UPC and IPC Sizing Charts
Especially for waste and vent sizing, the conversion from fixture units to pipe sizing is standard for all cases for the UPC and IPC. Generating sizing charts for cold and hot water, automatically through a series of settings possibly, would be probably more difficult to implement but equally helpful to make sizing plumbing easier.
6 votes -
Add Standard UPC and IPC Water Closet and Urinal Sizing Charts
In the UPC and IPC the conversion from water closet counts and urinal counts to a number of fixture units is a standard table. Adding this to Design Master would be a small change yet very helpful.
2 votes -
More customization for equipment callouts
Add more complicated options for callouts on equipment.
Add MCA and MOCP as notes on the callout on the drawing.
See images on this forum post for examples:
http://forums.designmaster.biz/index.php?showtopic=1817If you vote for this, it would be helpful if you could leave a comment letting us know what values you want displayed in the equipment callout.
3 votes -
Canadian Electrical Code Capability
As the word of this software is increasing in Canada, it would be a good idea to have the capabilities of incorporating the Canadian Electrical Code into Design Master.
3 votes -
Automatically Add a "Jog" When a Direct 90-degree Vertical at Wall Would Create an Overlap
Currently, when a Direct 90-degree Vertical at Wall returns back from the wall on top of the pipe going towards the wall, the pipe on top hides the underneath pipe. A common way of representing this in 2-D models is by adding a "jog" in the pipe. However, in the isometric model the jog doesn't need to appear because overlapping isn't a problem. Automatically showing this "jog" on the 2-D model would make representing these cases much easier.
1 vote -
add medium voltage conductors as an option when sizing conduits.
MV conductor insulation is much larger so you cannot get as many conductors inside a conduit. if you're using design master to calculate your feeder conduits it will be incorrect over 600v. I don't believe this is readily apparent now.
5 votes -
Having the ability to specify a breaker trip setting and plug size.
Add the ability to specify a breaker trip setting and plug size for adjustable trip breakers.
2 votes -
Insert Valves on Vertical Pipes
Be able to insert valves on vertical pipes. Valves would be displayed on isometric and possibly also on plan view.
2 votes -
Different layer systems for different loops and tick marks on a circuit
We can assign layers based on one-line (panel) or circuit or devices however not all parts of circuit are on the same layer. I may run some in the slab and some in the walls. Having the ability toi use the manual loop tool to change the layer system would be helpful. Also having the ability to assign a device to multiple layers would be helpful as well.
Or have some of the loops new and some existing.
5 votes -
Different Layers for New and Existing Items in Schedules
Use different layers for new and existing circuits in panel schedules or new and existing equipment in equipment schedules.
1 vote -
Importing Revit Model Information
It would be a great tool if we can have the ability to import model information from Revit drawings which are done by architects. A simple feature would be importing the rooms. This would speed up the process and make designs happen faster.
2 votes -
Low Voltage Homerun With Keynote
On low voltage systems drawings (Fire Alarm, Security, CCTV) we treat homeruns differently than power and lighting homeruns. We do not use the circuit label, wire callout, or tick marks, but rather we use a keynote. If there was a “keynote homerun”, it would save us the time spent removing the wire call-out every time we create low voltage homerun.
6 votes -
Vertical Alignment of Schedules
Add an option to control the vertical alignment of text in schedule cells.
Currently everything is justified to the top of the cell. Make it so that text can be centered or at the bottom instead.
1 vote -
Modify design load calculations and output to accommodate VAV system selection
Modify design load calculations to more accurately size/select VAV boxes. The revised calculations would take into account the heat required to overcome the additional air supplied to the VAV box that is over and above the minimum required in the heating calculations. This will help since the additional air is typically at 55 degrees and will actually add heat load to the space in addition to that required by the envelope and minimum supply air. In some cases this can be a significant load.
2 votes -
For Energy Code compliance, the light Fixture Schedule should include a subtotal of watts for each fixture type, and a total of watts for al
For Energy Code compliance, the light Fixture Schedule should include a subtotal of watts for each fixture type, and a total of watts for all the fixtures on the posted schedule. That will help expedite the Lighting Power Density calculations required for Energy Code Compliance.
2 votes -
1 vote
-
MULTIPLE ARROWS
It would be nice to be able to have multiple arrows for 1 piece of text pointing to different devices
2 votes -
Create training material for the HVAC section.
The tutorial doesn't get into enough depth or cover everything, specifically the master schedule and project schedules and how they affect the project.
2 votes
- Don't see your idea?