Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
374 results found
-
Photometrics: Combined Results Table
For Photometrics:
Request ability to combine results from each calculation zone into one large table. We have numerous zones and that many tables are hard to manage and look through and is not how we present our final results.2 votes -
Improve Dynamic Load Calculations
Make several modifications to fine tune the dynamic load calculations at the bottom of a panel schedule.
- Add the units of 'KVA' to the 'TOTAL LOAD'
- Change the units of the BALANCED LOAD line from 'A' to 'AMPS'
- Place the units for those two lines in the same column as the demand percentages of the rows above to make more room for the TOTAL LOAD and BALANCED LOAD sums to display without wrapping the units to the next line.
- Change the lines under CONN KVA and CALC KVA to the SCHEDULE-MEDIUM layer instead of the SCHEDULE-HEAVY…2 votes -
damage/withstand curves
Add the ability to add Transformer and conductor damage curves to the selective coordination graphs in the same manner as OCP devices.
1 vote -
Allow export to 64-bit Excel
The title says it all. Excel integration is currently not compatible with the 64-bit version of Excel.
1 vote -
reset
Would like it if we had the ability to reset all items we have overridden, even better if we could do it by category like wire size, breaker
2 votes -
Can make changes in Circuit Description
Change dash to a colon/semicolon to avoid confusion. Specially for a panel/s with two sections and dash is been use:, example panel N4 section 2 and a circuit -> N4-2-2,4,6 vs N4-2:2,4,6.
4 votes -
Additional voltage drop power factor options
Ability to pick .9 and .95 for power factor in options for voltage drop calculations in addition to the two we have, .85 or Revit.
2 votes -
Printing One Line Blocks
Suggest new feature to print all one line diagram blocks (distribution, feeder, equipment, etc) used in a project's block schedule. Would be a great tool when setting up the master template.
1 vote -
More flexible options for including room names in circuit descriptions
A few more options for circuit name based on space name please
• Don’t include space name
• Include space name and number
• Include space name1 vote -
Save manual tick mark settings per user, not per project
Save the tick mark settings in the "Insert Tick Mark" command per user, not per project.
Currently the settings are saved per project. If multiple people are using the command in a project, their settings overwrite each other. If a single person goes to different projects, their settings are not remembered.
2 votes -
Import Ductwork from Past Project Databases
Import ductwork and equipment from other databases. This facilitates additional projects at the same location. The thought is that if we can import the ductwork as existing from old projects, it would allow us to add/remove/modify ductwork much easier and quicker then re-drawing the existing ductwork from the previous project.
0 votes -
Panel Edit - AIC Rating to include Size Automatically Option
It would be nice to have Electrical DM Panel Edit to have an option for Fault Current - AIC Rating to include "Size Automatically" option, on top of the standard AIC ratings DM provides in the drop down option.
3 votesThis request wouldn't be hard, but it is one we've specifically avoided to this point. Our thinking is that the AIC rating of a panel is an important enough setting that we want it reviewed and set intentionally by the engineer.
-
Add capability to adjust Target Conduit fill at Panel Level and in options + Warning when exceeded
Sometimes I prefer to over-size conduit for various reasons. However, if this is done manually at the panel level and then the feeder / ampacity changes, its very easy to have a feeder that exceeds 40% fill. Proving an option to adjust the maximum fill from 40% would allow the user to over-size conduits without manually selecting a size.
Also, adding an alert that warns you when a feeder exceeds 40% (Similar to the panel threshold warning) would be a great add.
1 vote -
Prompt to Load DM
Add a prompt before loading any DM information into a project. Would be useful when you do NOT want DM loaded in a specific Revit project.
At the project level, would save your response so that you are only prompted once.
At the user level, would have an option to disable the prompt so DM is automatically loaded in all projects like it currently is for customers who prefer that workflow.
1 vote -
Upsize wire based on circuit length
Upsize the wire based on voltage and length. Example is we often have a note to use #10's for 120V 20A circuit greater than 100ft in length and 277V 210A circuit greater than 150ft in length.
3 votes -
Ability to Adjust Distribution Equipment Schedule
Currently the "Print Distribution Equipment Schedule" does not allow the option to adjust the column widths. The default column widths are too small for the circuit number and breaker and too large for the description. As a result when the schedules are printed they are often illegible or too wide to fit in the sleeves that come standard in panels.
1 vote -
People in Room Setting
Add an option to input people in a room using "People / 1000 sf" as the unit. Currently you can input people using "SF / Person" which requires a conversion from the numbers provided by some codes.
1 vote -
Auto update the feeder lengths on single line
when we move a panel/equipment, the feeders should not break, they should change their lengths as we move the panel connected to it, so that we don't have to refeed the whole thing again
2 votes -
Blank and Spare circuit differentiation
It would be nice if the 'SPARE' circuit label default could automatically change to something else (such as 'BLANK' or 'SPACE' if a circuit is set to have no breaker. This would look like two default names for unused circuits: one for unused circuits with a breaker and another for unused circuits without a breaker.
4 votes -
Find device without a homerun
This would work similar to 'find uncircuited devices' on a drawings, except that it would find circuited devices that aren't connected to a homerun.
3 votes
- Don't see your idea?