Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
206 results found
-
Homerun Note
Be able to add a note to a homerun callout.
5 votes -
Export Light Fixture Watts to Excel
Export the Energy Code Settings->Watts field from the light fixture schedule to Excel using the DM Electrical Excel Add-in.
4 votes -
Connect loops to fixtures on same switch first
When inserting automatic loops, connect devices on a switch together first rather than mixing up the loops when multiple switches are on a circuit.
3 votes -
Define fixed load by phase
When defining fixed load on a panel schedule allow entry of per phase loads on two and three phase circuits in stead of lumped loads, i.e., on 2-pole circuit be able specify a load for phase A and B on any of the demand categories.
2 votes -
Support Paralleled Generators Connected to Switchboard
DM does not currently support more than one source on the Normal side of an ATS or the EM side of ATS, however larger I-2, I-3 occupancies generally have paralleled generators connected to a switchboard. This feature would avoid cumbersome work arounds.
9 votes -
Electrical Symbol Legend
Add a Schedule of all blocks used in the project. This could be used a Symbol Legend for the Project.
46 votes -
please add a new column to the lighting fixture schedule for "KELVIN"
ADD NEW COLUMN IN LIGHT FIXTURE SCHEDULE FOR "KELVIN"
2 votes -
Light Fixture Settings - Different Blocks
The ability to define an egress fixture as the same fixture/block as the normal fixtures, with an option to turn a hatch on/off to differentiate. Similar to in Revit, where you can set an instance parameter and check it to turn fixtures into the egress blocks. The fixture type stays the same, only the visible block changes.
16 votes -
Voltage Drop in Equipment Schedule
Add "Voltage Drop" as a column to the equipment schedule. Would list the branch circuit voltage drop to a each piece of equipment in the schedule.
4 votes -
Simpler way to Change fonts in all your panel/switch box schedules
Right now, one has to edit all the blocks of a panel schedule in order to simply change the font. There should be a way to set the preferred font for all these schedules. If there is a way, I don't know about it. When I first set up DM 10 years or so ago, I do not remember having to change every block, but it's been so long ago...
4 votes -
Customizable tick marks
DesignMaster currently supports the following tick marks during an "Insert tick mark" operation:
- Hots
- Neutral
- Ground
- Iso ground
- Switch leg
- Traveller
- Space
We'd like the option to include customizable tick marks in addition to the ones already implemented above. For example, we include tick marks for low voltage cabling used to dim luminaries on our drawings.
I imagine the customization being performed through Design Master Electrical Options under the "Tick Mark Blocks" section. There'd be a "Customized tick mark 1 name" option and another option called "Customized tick mark 1 block". These customized tick marks would then show up in…
2 votes -
Default elevations for all electrical devices
You can specific a default elevation for light fixtures in the schedule. Expand this functionality to all types of electrical devices.
2 votes -
Do "Amps by Phase" using calculated loads on high-leg delta panels
High-leg delta panels are always unbalanced. The balanced 3-phase amps we display is not a good number to use when sizing these panels. The connected amps by phase does not account for largest motor loads or continuous loads.
Add the ability to determine the amps by phase using calculated loads. The largest motor, lighting, and continuous loads would all be calculated at 125%. All other loads would be calculated at 100%.
6 votes -
Tick marks for more than 1-pole, wire callouts for > #12
Add another option to "Homerun wire callouts and tick marks" labeled "Tick marks for more than 1-pole , wire callouts for > #12".
4 votes -
Change Voltage of Project
Be able to change voltage of a completed project for 208V to 240V and keep everything connected and circuited.
10 votes -
A spreadsheet like table, simular to the fault calculations, that shows all the load calculation fields by panel, as they move to the final
A spreadsheet like table, similar to the fault calculations, that shows all the load calculation categories by panel, as they move to the final service calculation. We could then turn the load calculation footer off on the panel schedules and include this summary table in the drawings. It would also be great to figure out how the loads are adding up.
4 votes -
Export schedules to excel
My estimators are always asking me if they can get my fixture or panel schedules in an excel format.
14 votes -
Add "Clear Circuit" Button Back to "Circuiting" Dialog Box
Add the "Clear Circuit" command back to the "Circuiting" dialog box. This button will set all the breaker and branch circuit sizing options back to "Size Automatically", set all the fixed loads to "0", and set the circuit descriptions to be blank.
3 votes -
Manufacturer Name field included within Notes Settings of distribution equipment
It would be helpful when creating distribution equipment lists if there was an option for the manufacturer's name. Currently we have to use an unused Note key, rename the label for that key and then remember which Notes Setting corresponds to the list entry.
1 vote -
Print Full Panel Schedules to 8.5x11 Sheets
Print full panel schedules, exactly as shown on the drawing, to a printer using 8.5x11 paper.
One specific use for these panel schedules would be to be submitted to Labor and Industries in Washington state for review.
3 votes
- Don't see your idea?