Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
57 results found
-
Save manual tick mark settings per user, not per project
Save the tick mark settings in the "Insert Tick Mark" command per user, not per project.
Currently the settings are saved per project. If multiple people are using the command in a project, their settings overwrite each other. If a single person goes to different projects, their settings are not remembered.
2 votes -
Add capability to adjust Target Conduit fill at Panel Level and in options + Warning when exceeded
Sometimes I prefer to over-size conduit for various reasons. However, if this is done manually at the panel level and then the feeder / ampacity changes, its very easy to have a feeder that exceeds 40% fill. Proving an option to adjust the maximum fill from 40% would allow the user to over-size conduits without manually selecting a size.
Also, adding an alert that warns you when a feeder exceeds 40% (Similar to the panel threshold warning) would be a great add.
1 vote -
Panel Edit - AIC Rating to include Size Automatically Option
It would be nice to have Electrical DM Panel Edit to have an option for Fault Current - AIC Rating to include "Size Automatically" option, on top of the standard AIC ratings DM provides in the drop down option.
3 votesThis request wouldn't be hard, but it is one we've specifically avoided to this point. Our thinking is that the AIC rating of a panel is an important enough setting that we want it reviewed and set intentionally by the engineer.
-
Arc-Flash Stickers based on NEC 110.16(B)
Create arc-flash stickers based on NEC 110.16(B). These stickers are much simpler than what are required by NFPA 70E.
0 votes -
Change default circuit callout
Add an option for the default circuit callout inserted on the drawing when connecting a device to a panel. Currently it always lists the full circuit callout of panel name and circuit number (P-1).
1 voteThe solution in the current software is to circuit the device then use the “Modify Circuit Label” command to change the callout.
-
Homerun Wire Callout Option
Add an option for homerun callouts to not display anything for #12 wires and to display tick marks and the full wire callout for anything else.
Currently there are a few options that are close but nothing that has exactly these groupings of tick marks and wire callouts.
0 votes -
Set default "Feeder length calculation method" to "Custom"
Be able to set the default "Feeder length calculation method" to "Custom".
0 votes -
Change default panel "Mounting"
Be able to set a different default value for the "Mounting" setting for panels and other distribution equipment.
0 votes -
I would like to be able to select a circuit number and highlight a device and draw a homerun, i.e. dedicated circuits, equipment, etc.
This would avoid the more cumbersome 2 step process
1. circuit device
2. draw homerunDepending on the job there are can be lots of dedicated circuits and/or pieces of equipment...
1 vote -
Customization of circuiting callouts
In circuiting callouts, allow the dash to be replaced by a custom string.
Example: Default circuiting callout is L1A-1,3,5. Allow us to make it say L1A: 1,3,5 or L1A CKT 1,3,5.
8 votes -
Spaces in Feeder Callouts
Be able to display feeder callouts with spaces after commas, instead of having all the wire sizes right next to each other.
Current Callout:
2''C,2#3/0,#3/0N,#6GDesired Callout:
2''C, 2#3/0, #3/0N, #6G3 votes -
Manufacturer Name field included within Notes Settings of distribution equipment
It would be helpful when creating distribution equipment lists if there was an option for the manufacturer's name. Currently we have to use an unused Note key, rename the label for that key and then remember which Notes Setting corresponds to the list entry.
1 vote -
Separate column in the feeder schedule for the service grounding electrode conductor.
The service ground does not get installed in the conduit with the service entrance conductors, so why is it shown just like all the other feeders where the equipment grounding conductor is installed with the feeder conductors. If you want the feature to show the GEC size, show it in a different column and show the feeder with no ground listed with the feeder conductors so its clear it is not in the conduit.
4 votes -
Add a hatch pattern to room definitions
When defining rooms, it is often difficult to determine which rooms have been defined and which have not, if an area gets surrounded. Adding a hatch pattern on its own layer would make it much easier to determine if you've included all room definition areas.
2 votes -
Reset panel "Fixed Loads".
Often, I need to "start over" on a panel that I've assigned fixed loads. It would be handy to have a button that would clear every fixed load on the panel. Or even be able to select several circuits and clear those circuit's fixed loads.
5 votes -
Equipment Panel Description
In the Panel Description dropdown, add "Equipment Callout + Description" to the list, in addition to "Same as Equipment Callout" and "Custom".
1 vote -
Default Groups
Have the ability to define a default device group name. In multi-phase projects it would be helpful to be able to set a group name as the default instead of having DM go to the "General" group.
1 vote -
Circuiting layer dependent on device layer system
DM's default circuit layer system can be determined by three different options: (1) same as distribution equipment, (2) new, and (3) existing. We'd like a fourth option that makes the circuit layer system match the circuit layer system of the device that's being circuited.
For example, we're currently designing a job where we are installing new receptacles that are being fed from an existing panel. Our receptacle circuit callouts are coming up under the existing layer system (based off of the panel) instead of the new layer system (based off of the new receptacles). To address this, we changed the…
1 vote -
Add load column to receptacle schedule
Add a column to the receptacle schedule to show the load on the receptacle.
1 vote -
Default label locations in blocks
Be able to specify locations for labels in blocks. When the labels are added to the block, they will be placed in the desired locations, rather than in the somewhat random default location they are currently placed in.
4 votes
- Don't see your idea?