Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
97 results found
-
4 votes
-
Customizable tick marks
DesignMaster currently supports the following tick marks during an "Insert tick mark" operation:
- Hots
- Neutral
- Ground
- Iso ground
- Switch leg
- Traveller
- Space
We'd like the option to include customizable tick marks in addition to the ones already implemented above. For example, we include tick marks for low voltage cabling used to dim luminaries on our drawings.
I imagine the customization being performed through Design Master Electrical Options under the "Tick Mark Blocks" section. There'd be a "Customized tick mark 1 name" option and another option called "Customized tick mark 1 block". These customized tick marks would then show up in…
2 votes -
Add "Panel Neutral" in Revit MEP
Add "Panel Neutral" as a parameter to panels in Revit MEP.
Options for neutral would be:
50%
100%
133%
200%
NoneThis value would be a shared parameter for scheduling purposes. It would not be used in any calculations.
2 votes -
Add "Clear Circuit" Button Back to "Circuiting" Dialog Box
Add the "Clear Circuit" command back to the "Circuiting" dialog box. This button will set all the breaker and branch circuit sizing options back to "Size Automatically", set all the fixed loads to "0", and set the circuit descriptions to be blank.
3 votes -
Manufacturer Name field included within Notes Settings of distribution equipment
It would be helpful when creating distribution equipment lists if there was an option for the manufacturer's name. Currently we have to use an unused Note key, rename the label for that key and then remember which Notes Setting corresponds to the list entry.
1 vote -
Print Full Panel Schedules to 8.5x11 Sheets
Print full panel schedules, exactly as shown on the drawing, to a printer using 8.5x11 paper.
One specific use for these panel schedules would be to be submitted to Labor and Industries in Washington state for review.
3 votes -
'Capped Ductwork for Future Use' command
This is similar to the 'end cap' command, but would draw a 'capped for future use' symbol on the end of a duct branch.
1 vote -
Schedules
Having the ability to adjust the width of a schedule in the drawing model, instead of the schedule toolbox.
1 vote -
Redefine Panel Schedule Blocks
Add a command to automatically erase and reinsert panel schedules so that attribute locations are updated correctly.
Currently, you have to manually erase the schedule, redefine the block, and reinsert the schedule.
1 vote -
Export Equipment List to Excel
Export a list of equipment connections and information to a file that can be opened and viewed in Excel. The file would be for post-processing only. Any changes to the equipment would still be made using the other DM commands.
28 votes -
Command to Automatically Turn Photometric Layers On and Off
It would be nice to have ribbon menu icon commands to turn the photometric layers on and off as well as automatically turn the respective layer back on after doing a recalc of either general or egress lighting.
2 votes -
Total Load in Project
Please add capability to total loads for the project before the circuiting is complete.
I would like to have a load sheet that keeps track of the total project load.
What I use now is a modified panel shedule that only shows the loads for a dummy panel I create called service. I connect all the panels together and then to Service. This gives me a total load analysis for the project, but only after the design is complete. I need to be able to confirm my loads and service sizing at the design development stage before circuiting.
A consideration…
9 votes -
Add command to match diffuser callout and location; just like you have for light fixtures.
It would be nice to at least have the command to match diffuser callout location.
5 votes -
Show Locked CFM in Duct Centerline
I have been back into DM after a short break away from it's use. I have found that text now appears along the center line referencing that the width, depth, or shape of the duct has been locked. This is a great new feature. However, I feel that one of the most important features that could be shown as locked is that of the CFM. In a quick duct sizing and CFM check, by locking the CFM of the end duct in the various branch strings, one can size and determine very quickly how a system is going to be.…
1 vote -
Import single piece of equipment
Currently, the "Import Equipment from Another Project" command imports all the equipment. Update that function to allow you to choose specific pieces of equipment to import.
3 votes -
Equipment Panel Description
In the Panel Description dropdown, add "Equipment Callout + Description" to the list, in addition to "Same as Equipment Callout" and "Custom".
1 vote -
Default Groups
Have the ability to define a default device group name. In multi-phase projects it would be helpful to be able to set a group name as the default instead of having DM go to the "General" group.
1 vote -
Find Unlooped Devices
A function similar to “Find Uncircuited” that finds elements that are circuited but have not been looped – “Find Unlooped” or something of that nature. I often am at risk of missing a dedicated receptacle or single equipment connection that I circuited, but missed when I was going through the looping/home run process.
3 votes -
Circuiting layer dependent on device layer system
DM's default circuit layer system can be determined by three different options: (1) same as distribution equipment, (2) new, and (3) existing. We'd like a fourth option that makes the circuit layer system match the circuit layer system of the device that's being circuited.
For example, we're currently designing a job where we are installing new receptacles that are being fed from an existing panel. Our receptacle circuit callouts are coming up under the existing layer system (based off of the panel) instead of the new layer system (based off of the new receptacles). To address this, we changed the…
1 vote -
Minimum panel clearance width
For panels smaller than 30" width, increase the panel clearance width to 30" automatically.
3 votes
- Don't see your idea?