Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
156 results found
-
Make Grips Work With Diffuser Callouts
Fix the diffuser callouts so they can be moved more consistently and reliable with grips instead of using the "Move Callout" command.
1 vote -
7 votes
-
Acoustical Calculations
Add acoustical calculations to the ductwork.
1 vote -
Generic Schedule Creator
Have a way to create a generic schedule. The schedule will be informational purposes only, but it will be generated the same way as the other DM schedules so it will look the same.
29 votes -
Add multiple circuits to a single piece of equipment (ie. HVAC) one for each load.
Some HVAC and other pieces of equipment require multiple circuits for multiple loads inside each unit. Currently I have to create 2 pieces of equipment with the individual loads, overlay them, then circuit them.
29 votes -
Set Room Exhaust Rate
Specify the exhaust air requirements for rooms and use these numbers in the load calculations and duct design calculations.
27 votes -
Improve Indoor Lighting Level Report
Add "Allowed Watts / SF" as a field to rooms.
Add "Allowed Watts / SF" and "Total Allowed Watts" as columns to the indoor lighting schedule.
Add a "Totals" row at the bottom that totals the area, allowed watts, and computed watts.
3 votes -
Draw Circuit Loops Using Polylines instead of Arcs
When you loop from one device to another, be able to select that loop and break it in to two loops that can each individually be moved or broke. This way we can have "S" loops.
DM Note: When we implement this, it will probably be by allowing you to insert a loop using a pline. This will allow you to insert the loop however you want without any restrictions.
20 votes -
Keep Tick Marks on Broken Circuits
When a circuit is broken, keep tick marks inserted on one of the halves.
11 votes -
2 votes
-
Create Separate One-Lines for Each LVD Group
I have Security, F/A, Lighting Control Panels, Audio, and Data groups and would like to be able to create separate low voltage one-line risers for them.
13 votes -
Photometric calculation schedule
I would like to suggest that the photometric calculation schedule be a combined schedule for all rooms instead of a dedicated schedule for each single room/space (or both options be available). We are typically asked to provide a single schedule that lists the room/space name in the first column and then the various footcandle columns.
2 votes -
Allow diffuser tags to be moved and modified with standard AutoCAD editing commands.
It would be helpful to not have to use the "special" DM commands to manipulate the diffuser tags.
13 votes -
Select automatic conduit based on Type
When selecting conduit I want to be able to select the feeder as schedule 80 so that the only size option would be based on schedule 80. Then on another feeder I could select EMT for my circuits and the only option for auto sizing would be based on EMT. Finally, I would then have the option of adding the type to my one-lines and a conduit schedule.
11 votes -
Lighting loads - additional options
I like the recent addition of the general lighting loads, but there are a couple of additional things that I would like to see related to that.
- I think that the calculated load should include the greater of the general lighting load or the connected lighting load. The NEC states that the values for the general lighting loads are minimum values and that they may not be adequate.
Ok, so this is probably a low priority because the NEC values are pretty conservative. With the increased adoption of energy conservation codes it becomes less likely that the connected lighting load…
2 votes -
Generator Load Calculations
Calculate generator loads correctly, mostly by being able to specify that certain loads should not be included in the generator load.
1 vote -
Existing Loads & Metered Demand
Include, in options, the ability to not include existing (layered) items in panel, feeder, and service calculations. I'd like to enter the load to keep track of it, but have the ability to exclude it from the load calculations since "existing" would be included in the metered demand load.
1 vote -
Dash in Empty Schedule Cells
Include an option to print a "-" (a dash) in schedule cells if nothing is printed in them.
1 vote -
Equipment circuit label should be near the equipment symbol--not the equipment label.
We often turn off printing of equipment label/leader, and use a keynote number with arrow instead. But we have to move the circuit to the equipment symbol, because it ends up under the equipment label (which we are not printing).
2 votes -
Automatically Add "ON" prefix to homerun labels for which a homerun already exists.
It is customary for circuits that are shared on opposite ends of a building or from one floor to the next to be identifed with multiple homerun symbols, with all but one of those homeruns labeled with "ON <Panel-Ckt>" rather than connecting with a loop. Currently, to do this, the homerun text itself must be modified, and this rarely works well because that text reverts back to the default <Panel-Ckt> text each time the circuits are updated.
1 vote
- Don't see your idea?