Design Master Wish List
Welcome to the Design Master Wish List, where you can submit your ideas for improvements to the software.
17 results found
-
Add parameter for upstream equipment fault value that includes motor
The only parameter I see for upstream fault is (DMETFaultFedFromFault). This is the upstream fault value from Utility, but does not include motor fault. Can a parameter be added that shows the total value including the motor fault of the upstream equipment?
1 vote -
Circuit Comments
Add comments to circuits in the Circuit Edit command. Transfer the comment value to the circuit and to the devices connected to the circuit.
This feature would allow additional information from a circuit to be scheduled on the devices. It would be similar to how DM currently pushes the breaker size to from the circuit to the device that can then be used in equipment schedules.
6 votes -
Upsize wire based on circuit length
Upsize the wire based on voltage and length. Example is we often have a note to use #10's for 120V 20A circuit greater than 100ft in length and 277V 210A circuit greater than 150ft in length.
3 votes -
Size ground and isolated ground separately
Add an option to the isolated ground to size it to a specific value. Currently it is an on/off toggle and sized to match the ground wire.
1 vote -
Selective Coordination Graph: Fault Options
The fault labels are currently displayed automatically at the top of the selective coordination graphs.
Add an option to display the fault at the top (current functionality), at the bottom (current label would move to the top of the graph), or remove them.
1 vote -
Selective Coordination Graph: Set minimum time
Be able to set the minimum time for selective coordination graphs. Currently it is fixed at 0.01. We could add an option to set it at 0.1 or 0.01. Or add an option to set it at a specific value.
We are leaning toward implementing it as a 0.1 or 0.01 option. If you would like it as a custom value, indicate that in the comments.
1 vote -
Grounding Electrode Conductor for Transformers
Size and label the grounding electrode conductor (GEC) for transformers based on NEC 250.66.
5 votes -
Customize Parallel Run Labeling
Add customization options for how multiple parallel runs are labeled for wires.
DM currently labels multiple sets with the number of sets in parenthesis before the full wire callout:
(3) 3-1/2"C, 4-600kcmil, 3/0G
If you are interested this feature, indicate in the comments how you would like the multiple runs labeled.
2 votes -
Adjust Transformer Taps
Be able to adjust transformer taps to take care of voltage drop.
1 vote -
Ability to add multiple set of conductor in a single conduit
Example:
For 400A feeder:
(2) 3"C, 3-250kcmil AL, 250kcmil AL N, #1 AL G
(1) 4"C, 6-400kcmil AL, 2-400kcmil AL N, #1 AL GInstead of each set take (1) conduit, would be good to get multiple set into a single conduit. This is mainly because installing (1) 4" conduit is cheaper than (2) 3" conduits.
1 vote -
Single Line-to-Ground Faults
Calculate single line-to-ground faults (NEC 230.95).
1 vote -
DC arc flash
Incorporate DC Arc Flash calculations. A lot of design work now has an element of renewable energy devices - solar, wind, etc. And many of those have battery 'peak shaving' capability. Being able to calculate both AC and DC arc flash given the electrical model will provide a one-stop-shop for arc flash. I would not rely so heavily on SKM. Thanks!
2 votes -
Room Names in Circuit Description
Provide an option for Room Names analogous to the "Conduit location" Option. Also consider other customization:
-Custom Room prefix - e.g. RM
-Option to include/exclude Name - e.g., RM 120
-Option to include/exclude Number - e.g., RM FIRE RISERRoom Names Location:
->Start of Circuit Description
->End of Circuit DescriptionCurrently the room names always go at the end, just like OOTB Revit. Having the option to put the room at the start would allow for better scheduling for when the intent is for circuits to be organized by room, like so:
https://i.postimg.cc/qMFD3DLx/2019-01-30-13-12-16-Window.png4 votes -
Include "1" before single ground and neutral wires
Add an option to include a "1" in the wire callout before single ground and neutral wires. Currently the wire size is listed with no count before it.
Current wire callout:
1/2"C, 1#12, #12N, #12GNew wire callout:
1/2"C, 1#12, 1#12N, 1#12G4 votes -
Specify fault at upstream device
Be able to specify the fault at the upstream device, rather than at the current device. This feature would be useful when you want to specify the fault at the utility transformer but it is not included in the Revit model.
3 votes -
Add "Panel Neutral" in Revit MEP
Add "Panel Neutral" as a parameter to panels in Revit MEP.
Options for neutral would be:
50%
100%
133%
200%
NoneThis value would be a shared parameter for scheduling purposes. It would not be used in any calculations.
2 votes -
Prompt to Load DM
Add a prompt before loading any DM information into a project. Would be useful when you do NOT want DM loaded in a specific Revit project.
At the project level, would save your response so that you are only prompted once.
At the user level, would have an option to disable the prompt so DM is automatically loaded in all projects like it currently is for customers who prefer that workflow.
0 votes
- Don't see your idea?